POLISHING SUPPLIES FOR SAMPLE PREPARATION
Polishing is the most crucial step in preparing a specimen for microstructural analysis. It is the step which is required to eliminate previous damage.
Ideally, the amount of damage produced during cutting and grinding was minimized through the proper blade and abrasive grinding so that polishing can be reduced.
To remove deformation from fine grinding and obtain a highly reflective surface, the specimens must be polished before they can be examined under the microscope. Polishing is a complex activity in which factors such as quality and suitability for the cloth, abrasive, polishing pressure, polishing speed and duration need to be taken into account. The quality of the surface obtained after the final polishing depends on all these factors and the finish of the surface on completion of each of the previous stages.
There are three types of polishing cloths; Woven, Non-Woven, and Flocked.
• Woven cloths offer ‘hard surface’ polishing properties and guarantee flat pre-polishing,
without deterioration of the edges.
• Non-woven cloths are used on very hard materials for high precision surface finishing such
As glass, quartz, sapphire, and semiconductors.
• The Flocked cloths, guarantee a super-polished finish. The polishing duration must be as
short as possible, to avoid inclusions from being extracted.
Diamond, due to its exceptional hardness and cutting capacity, has become the first choice abrasive in metallographic polishing. Diamonds for metallographic grinding and polishing are available in two different crystalline shapes: Polycrystalline (P) and monocrystalline (M). Polycrystalline diamonds provide vast numbers of small cutting edges. In the metallographic preparation process, these edges result in high material removal, while producing only a shallow scratch depth.
Monocrystalline diamonds are more block-shaped and provide few cutting edges. These diamonds give high material removal with a more variable scratch pattern. For high requirements, the (P)-type diamonds are chosen. The (M) type diamonds are best suited for all-purpose polishing. Diamond products are usually available in three forms; diamond paste, diamond suspension, and diamond spray.
Polycrystalline diamond as compared to monocrystalline diamond provides better surface finishes and higher removal rates for metallographic specimen preparation. The features and advantages of polycrystalline diamond include the following:
• Higher cutting rates
• Very uniform surface finish
• More uniform particle size distribution
• Higher removal rates (self-sharpening abrasives)
• Harder/tougher particles
• Blocky shaped
• Hexagonal micro crystallites (equally hard in all directions)
• An extremely rough surface (more cutting points)
• Surface area 300% greater than monocrystalline diamond
• No abrasion-resistant directionality (abrasion independent of particle orientation)
Final Polishing Abrasives
Final polishing abrasives are selected based upon specimen hardness and chemical reactivity. The most common polishing abrasives are alumina. Alumina abrasives are primarily used as mechanical abrasives because of their high hardness and durability.
- Polishing Fixation Systems
- Premium Polishing Cloth
- Polycrystalline Diamond Suspension (Water) (4 Series)
- Polycrystalline Diamond Suspension (2 -in 1) (DIA-LUBE) (2 Series)
- Polycrystalline Diamond Suspension (Alcohol)
- Monocrystalline Diamond Suspension (Water)
- Monocrystalline Diamond Suspension (2-IN-1)
- OIL Series Monocrystalline & Polycrystalline Suspensions
- GLYCOL Series Monocrystalline & Polycrystalline Suspensions
- Diamond Aerosol Sprays
- Diamond Aerosol Sprays (NON HAZARDOUS)
- Lubricants and Extenders
- Diamond Compound Paste
- OPS Colloidal Silica & Premium OPS Colloidal Silica (2 Series)
- Colloidal Silica Non-Crystallizing & Crystallizing (2 Series)
- Alumina Powder & Premium Alumina Powder (2 Series)
- Alumina Suspension & Premium Alumina Slurry (2 Series)
- Monocrystalline Alpha Alumina Powders
- Aluminum Oxide Powder (White)
- Silicon Carbide (SiC) Powder
- Aluminum Oxide Lapping Film
- Diamond Lapping Film
- Silicon Carbide Lapping Film
- Cerium Oxide Resin Bonded Disks
- Cerium Oxide Resin Bonded Belts
- Cerium Oxide Slurries
- Alumina Compound Paste
- Abrasive Powders
- Polishing Cloth - Old Favorites
- Polishing Cloth Accessories
- Polishing Cloth