Menu
Your Cart

Micro Injector Nozzle, Pack of 15 (REP-MROG-06D) by Metallurgical Supplies metallurgicalsupplies.com

Free shipping Over $1,000
Micro Injector Nozzle, Pack of 15 (REP-MROG-06D) by metallurgicalsupplies.com from META-RUBBER Orange Medium Body
Secured Shopping
Best security features
Free Shipping
Free delivery over $1,000

Technical Specifications

Casting Solutions Replicating Specs
ColorFinal Color Orange
Product NameMETA-RUBBER Orange Medium Body
Product Size15 Pack
Micro Injector Nozzle, Pack of 15 (REP-MROG-06D) by Metallurgical Supplies metallurgicalsupplies.com
  • Stock: 1000
  • Reward Points: Receive 0 - META-POINTS
  • Model: REP-MROG-06D
  • Weight: 2.00kg
  • Dimensions: 7.00 x 7.00 x 3.00
  • SKU: REP-MROG-06D
190 samples sold

Ask anything related to the product

There are no questions for this product.

Micro Injector Nozzle, Pack of 15 (REP-MROG-06D) - META-RUBBER Orange Medium Body by Metallurgical Supplies

 Micro Injector Nozzle, Pack of 15

 

META-RUBBER Orange Medium Body is a two-component, addition cured, platinum-catalyzed, hydrophobic vinyl polysiloxane. Its two components are extruded from a double-barreled cartridge, through a static mixer to obtain a uniform mixture. It may be used to reproduce surface characteristics. It is able to reproduce surfaces down to submicron particles or scratches. It is cured at room temperature. However, warmer temperatures accelerate the setting time and cooler temperatures slow the setting time.

A mixing and dispensing system that enables you to make quick and accurate replicas, without manual mixing and fuss!

META-RUBBER ORANGE System consists of 4 kits with various combinations of the following:

  • 50ml dual-barrel syringe with reusable end cap; easily filled by pouring contents of into cartridge barrels.
  • Disposable low-cost Helix Mixing Nozzle Tips easily attach to and detach from dual-barrel syringe.
  • REPRO-MIX™ II Dispensing Gun.

META-GREEN THIN POUR System consists of 4 kits with various combinations of the following:

  • 50ml dual-barrel syringe with reusable end cap; easily filled by pouring contents into cartridge barrels.
  • Disposable low-cost Helix Mixing Nozzle Tips easily attach to and detach from dual-barrel syringe.
  • META-MIX II Dispensing Gun.

META-RUBBER Orange Medium Body Physical Properties

Determined at 23°C (72°F) (Tested according to ISO 4823)

Base Paste

Appearance - Homogenous orange-colored runny paste, Filling loading approximately 25% silicon dioxide.


Catalyst Paste

Appearance - Homogenous, grey-colored runny paste, Filling loading approximately 25% silicon dioxide.

Mixed Material

Appearance - Homogenous orange-colored.

Mixing Time (prior to gelation)

Dispensing time depends on mass extruded.


Working Time

2.0 – 2.5 minutes


Setting Time

5 – 6 minutes. Varies with ambient temperature. Warmer temperatures accelerate the setting time. Cooler temperatures slow the setting time.


Compression Set (Recovery from deformation)

1.0%

Strain in Compression (A modified Modulus of Elasticity)

4-5%


Shore A55

Detail Reproduction

  • Smaller than 20-micron line
  • Contact Angle @ 0 minutes 65°
  • Contact Angle @ 15 minutes 5°
  • Contact Angle @ 30 minutes 5°

Dimensional Change

  • After 1 hour- 0.30% Change (negative 0.30% change) this means it shrinks 0.30%
  • After 24 Hours - –0.35 % Change (negative 0.35% change) this means it shrinks 0.35%
  • After 7 Days - –0.40 % Change (negative 0.40 % change) this means it shrinks 0.40%

Tear Strength

300-325 psi

Percent of Elongation

70%

Modulus of Elasticity

770


Flash Point of the polymers used

130°C (266°F)


Ignition Temperature of the Polymers Used

470°C (878°F)

Fully set material may be autoclaved, but its dimensional stability may be compromised. If allowed to return to room temperature, it should return to the original shape.


Disinfection

Since material is hydrophobic, immersion in disinfectants is acceptable, but should not be immersed in the disinfectant for longer than 10 minutes. The surface color may change due to the disinfectants used.

Applications

You can take impressions of:

  • All Metals
  • Non Metals
  • Paper or Cardboard Items
  • Ceramic and Glass items
  • Wood, Marble, etc.
  • All Plastics
  • Rubber


Other Uses Include:

  • Fixturing where the semi-rigid structure is desired.
  • Making joints where flexibility is required.
  • The replica is easy to remove - even if there are undercuts or grooves.
  • Cross-sectioning of the replica is easily accomplished with a knife or razor.
  • It can then be checked on an optical comparator or microscope.
  • Surface finish replication is exact with excellent optical properties.
  • Replicas are permanent - will not leach or ooze out nor outgas.
    Prototypes of rubber type components such as gaskets, washers, etc.
  • As a mask for high-temperature plasma spray of metallic coatings.
  • No more 16 hour cure time as with RTV silicones
  • More accurate than all other RTV compounds
  • Putty will withstand up to 600°F (or more).
  • Copies can be recopied (copy from a “female mould” yields a male-shaped replica).

Write a review

Note: HTML is not translated!
BadGood
Captcha

There are no downloads.